Products
Flange Mounted Overrunning Clutch

Flange Mounted Overrunning Clutch

The Flange Mounted Overrunning Clutch is designed for industrial drive systems that require one-way torque transmission, overrunning, or backstopping. It uses a sprag-type locking mechanism to transmit torque in the driving direction and allow relative rotation when the driven member overruns the driving member.

Product Configuration and Operating Features

The Flange Mounted Overrunning Clutch is designed for industrial drive systems that require one-way torque transmission, overrunning, or backstopping. It uses a sprag-type locking mechanism to transmit torque in the driving direction and allow relative rotation when the driven member overruns the driving member.

The flange-mounted configuration provides a mounting interface for installation into compatible industrial equipment. Its ball-bearing-supported structure supports relative rotation between the inner and outer components during operation.

The clutch features a keyed inner race connection for torque transmission through the connected shaft. Depending on the selected configuration, sealing and lubrication arrangements can include oil lubrication with lip seals or grease lubrication with labyrinth seals.

This configuration is intended for heavy-duty industrial transmission systems where the required torque capacity, operating speed, shaft connection, and installation dimensions must be matched to the application.

Technical Specifications and Model Selection

The following table lists the available size configurations and their corresponding torque and speed specifications.

Model Size Rated Torque (Nm) Max. Inner Race Speed (RPM) Max. Outer Race Speed (RPM)
1051 51,680 400 50
1250 63,920 170 40
1300 93,840 140 35
1375 149,600 130 30
2000 272,000 100 25
2400 333,200 85 20
3500 476,000 80 20
5000 680,000 75 20

The listed torque capacity ranges from 51,680 Nm to 680,000 Nm across the eight size configurations. The maximum inner race speed ranges from 75 to 400 RPM, while the maximum outer race speed ranges from 20 to 50 RPM.

These values correspond to different model sizes and should not be treated as interchangeable operating limits. Select the model according to the required torque capacity and the actual speeds of both races.

Before selecting a clutch, consider the operating torque, starting and peak loads, driving speed, overrunning speed, operating cycle, and installation arrangement. The selected model should be checked against the equipment's actual operating conditions.

Flange Mounting and Shaft Connection

The flange-mounted design provides a bolted mounting interface for integration into compatible industrial drive assemblies. The mounting structure should be matched to the equipment housing or supporting component to maintain the required installation alignment.

The keyed inner race connects to the corresponding shaft and transmits torque through the key connection. The shaft diameter, key dimensions, flange interface, and mounting hole arrangement must be checked against the selected model's dimensional drawing.

Installation alignment and the condition of the supporting structure are important considerations when integrating the clutch into an industrial transmission system. Confirm the available installation space and connection dimensions before ordering.

Exact flange dimensions, bore dimensions, keyway measurements, and mounting tolerances should be verified from the technical drawing for the required model.

Sprag Mechanism, Bearing Support, and Lubrication

The sprag locking mechanism enables the clutch to transmit torque in one direction and release during overrunning. When the driving race rotates in the locking direction, the sprags engage between the inner and outer races to transfer torque. When the relative rotation changes to the overrunning direction, the sprags release to allow free rotation.

The ball-bearing-supported structure accommodates relative rotation between the clutch components. The keyed inner race provides the shaft connection required for torque transmission.

Lubrication and sealing arrangements depend on the selected configuration. Available arrangements include oil lubrication with lip seals and grease lubrication with labyrinth seals.

When specifying the clutch, confirm the required lubrication method, sealing arrangement, operating environment, and maintenance conditions. The selected configuration should be compatible with the equipment's operating requirements.

Industrial Applications

Flange Mounted Overrunning Clutches can be considered for industrial equipment that requires one-way torque transmission or backstopping in a heavy-duty drive system.

Typical application areas include:

Conveyor Systems: Used in conveyor drive assemblies where reverse rotation must be restricted when the drive stops or when the load applies reverse torque.

Bucket Elevators: Applied in lifting and conveying equipment where backstopping is required to prevent reverse movement under load.

Industrial Gearboxes: Integrated into compatible gearbox arrangements to provide one-way operation or overrunning functionality.

Material Handling Equipment: Used in heavy-duty transmission systems where controlled torque transmission and prevention of reverse rotation are required.

Industrial Processing Equipment: Considered for machinery with rotating drive assemblies that require a one-way clutch function.

Final application suitability depends on the required torque, operating speeds, mounting interface, and actual load conditions.

Selection Factors and Customization

Choosing a suitable Flange Mounted Overrunning Clutch requires more than matching the nominal torque rating. The following information helps establish compatibility with the target equipment:

Torque Requirements: Specify the normal operating torque, peak torque, and any starting or transient loads that the clutch must handle.

Operating Speeds: Provide the driving race speed and overrunning race speed. Both values should be checked against the limits of the selected model.

Shaft Connection: Confirm the inner race bore, shaft diameter, keyway dimensions, and required connection arrangement.

Flange Interface: Provide the mounting dimensions, bolt-hole arrangement, and available installation space.

Lubrication and Sealing: Identify the required oil or grease lubrication arrangement and the sealing configuration according to the operating environment and maintenance requirements.

Xiamen Shuilin Zhitou Technology Co., Ltd. states that drawing-based and sample-based customization is available for mechanical components and equipment. For special clutch requirements, provide the existing model number, technical drawing, or equipment interface details for review.

Any non-standard dimensions or configuration requirements need to be checked for compatibility with the selected clutch model before order placement.

Supply Capabilities and Technical Support

Xiamen Shuilin Zhitou Technology Co., Ltd. is a China-based trading supplier engaged in the import and export supply of industrial transmission components and electromechanical equipment. Its company profile describes more than ten years of related trading experience and a supply network involving transmission component suppliers in Europe, America, and Japan.

Its product supply scope includes industrial clutches, overrunning clutches, reducers, electric motors, servo motors, and couplings. The company also states that drawing-based and sample-based customization services are available for mechanical components and equipment.

For Flange Mounted Overrunning Clutch requirements, the supplied model information, torque rating, speed requirements, shaft connection, and mounting interface can be reviewed before quotation.

These are company-level trading and supply capabilities. They should not be interpreted as claims that the company owns the factories or manufacturing facilities of the supplied products.

Request a Quote

To request a quotation for a Flange Mounted Overrunning Clutch, provide the required torque capacity, inner race speed, outer race speed, model size, shaft bore and keyway dimensions, flange mounting details, lubrication requirements, and order quantity.

If you are replacing an existing clutch, a model number, nameplate photo, dimensional drawing, or equipment installation photo can help identify the required configuration.

For new equipment projects, provide the drive system layout and operating conditions so that the clutch model and installation compatibility can be reviewed.

The model, technical specifications, mounting dimensions, and available configuration options can then be checked against the supplied information before quotation.

Hot Tags: flange mounted overrunning clutch, China flange mounted overrunning clutch suppliers, factory

Send Inquiry