Products
FLENDER N-EUPEX Flexible Pin And Bush Coupling

FLENDER N-EUPEX Flexible Pin And Bush Coupling

The FLENDER N-EUPEX is a torsionally flexible pin coupling for connecting two shafts in industrial drive systems. Its elastomer elements provide torsional flexibility and damping while allowing the coupling to accommodate limited shaft misalignment.

Product Overview

The FLENDER N-EUPEX is a torsionally flexible pin coupling for connecting two shafts in industrial drive systems. Its elastomer elements provide torsional flexibility and damping while allowing the coupling to accommodate limited shaft misalignment. The series covers a wide range of nominal torque requirements, with different sizes and construction types for different installation conditions.

Two relevant configurations are Type A and Type H. Type A has a three-part construction that allows the elastomer elements to be replaced without moving the connected machines. Type H uses a spacer arrangement where additional distance between the shaft ends is required.

N-EUPEX is a pin coupling. It should not be confused with the FLENDER RUPEX pin and bush coupling series, which has a different design and torque range.

Key Features

  • Torsional flexibility: Elastomer elements provide torsional flexibility and help dampen torsional vibration in the drive system.
  • Misalignment compensation: The coupling accommodates limited radial, angular and axial shaft displacement within the applicable model limits.
  • Multiple construction types: Type A and Type H provide different installation arrangements.
  • Elastomer options: NBR and selected TPU elements are available, with different hardness options for specific operating requirements.
  • Maintenance access: The Type A construction allows elastomer replacement without separating or repositioning the connected machines.
  • Size range: The N-EUPEX series includes 23 sizes, covering nominal torque ratings from 12 to 85,000 Nm.

Technical Specifications

Parameter N-EUPEX Series Information
Coupling type Torsionally flexible pin coupling
Series FLENDER N-EUPEX
Construction types covered Type A, Type H
Nominal torque range 12–85,000 Nm
Number of sizes 23
Coupling body material Cast iron
Elastomer materials NBR and selected TPU; fabric-reinforced NBR options are also specified in the series range
Standard elastomer hardness 80 Shore A
Other elastomer hardness options 65, 90 and 97 Shore A, depending on the applicable configuration
Series operating temperature range -50°C to +100°C; the applicable limit depends on the elastomer
Shaft connection Bore with keyway or other specified shaft connection

The torque range and temperature range above describe the N-EUPEX series, not the rating of every individual size or elastomer combination. Final selection requires the exact coupling size, elastomer type and operating conditions.

Representative Size Data

The following examples show selected Type A and Type H configurations. Torque figures are based on 80 Shore A elastomer elements.

Configuration Size Rated Torque Maximum Speed Maximum Bore
Type A 110 160 Nm 5,300 rpm D1: 48 mm; D2: 38 mm
Type H 80 85 Nm 7,200 rpm 38 mm
Type H 95 140 Nm 6,600 rpm 48 mm

These figures apply to the listed size and configuration. They should not be transferred to other sizes. The selected coupling must also meet the required shaft dimensions, operating speed, torque and permissible misalignment.

Coupling Configurations

Type A Pin Coupling

Type A uses a three-part construction with elastomer elements fitted between the coupling components. Its arrangement allows the elastomer elements to be replaced without moving the connected machines. This can simplify maintenance where the motor and driven equipment are installed in a fixed position.

Type H Spacer Coupling

Type H uses a spacer arrangement to provide a greater distance between the connected shaft ends. It is relevant where the installation layout requires additional shaft separation. The required spacer arrangement and dimensions should be checked against the equipment layout before ordering.

Applications

N-EUPEX couplings are used in industrial drive systems where torsional flexibility and shaft misalignment compensation are required. Typical equipment includes:

  • Pumps and compressors in process and utility systems.
  • Fans and blowers in industrial ventilation and air-handling equipment.
  • Mixers and agitators used in chemical and process plants.
  • Drive systems in mining, cement, power generation and metal processing.
  • Machinery used in pulp and paper, plastics and rubber, and water and wastewater treatment.

The coupling size and elastomer selection should be based on the actual drive conditions rather than the equipment category alone.

Key Selection Factors

Required torque and service conditions

Confirm the nominal torque, starting torque, load variation and operating duty. The selected size must meet the applicable torque requirements under the actual operating conditions.

Operating speed

Check the required speed against the maximum permissible speed for the selected coupling size and configuration. A speed rating from one size should not be used to assess another.

Shaft dimensions and connection

Provide both shaft diameters, available shaft lengths, keyway dimensions and the required hub arrangement. These details are essential for checking bore compatibility and installation fit.

Installation arrangement

Choose Type A or Type H according to the available shaft-end distance and maintenance access. For Type H, confirm the required spacer length and overall installation dimensions.

Elastomer selection and misalignment

Confirm the operating temperature and required elastomer hardness. Check radial, angular and axial misalignment against the permissible values for the selected size and operating speed.

N-EUPEX Coupling Supply

As a China-based industrial transmission equipment and components supplier, we supply products associated with FLENDER, SEW and other industrial drive brands. For N-EUPEX coupling enquiries, the required series, construction type and size should be identified before confirming the product configuration.

Type A and Type H are relevant configurations for product identification. Supply enquiries can be checked using the coupling model, article number, nameplate information, existing component dimensions or equipment drawings. Complete coupling assemblies and replacement-component requirements should be stated separately so that the requested supply scope can be identified accurately.

Product origin, exact configuration, availability and delivery schedule should be confirmed against the specific enquiry. A product listing or series designation alone does not establish original-manufacturer authorization or stock status.

Request a Quote

To help identify the correct N-EUPEX coupling, please provide:

  • Coupling model, size or article number, if available.
  • Required quantity.
  • Type A or Type H configuration, if known.
  • Shaft diameters, keyway dimensions and available shaft lengths.
  • Required spacer length or installation dimensions for Type H.
  • Existing nameplate photos, coupling drawings or equipment details.
  • Whether you need a complete coupling assembly or replacement components.

If the existing model is unknown, send the available dimensions and equipment information for product identification and compatibility checking.

Hot Tags: flender n-eupex flexible pin and bush coupling, China flender n-eupex flexible pin and bush coupling suppliers, factory

Send Inquiry